testing adjusting balancing Tigard OR 97224

commissioning portland Bull Mountain Tigard OR 97224

a list of corrections that can be implemented in the plan

The verification of the temperature control system

Excel file for testing dampers that lists access requirements

The year 2003 marked the beginning of NorthWest Engineering Service Inc.'s work on FLS systems. Because of our extensive experience in Commissioning (Cx) and Testing, Adjusting, and Balancing (TAB), we are in a truly unique position to carry out audit surveys of HVAC systems, identify and functionally test all Fire Smoke Dampers, and offer documentation to meet the standards of the AHJ.

Investigation in the field and labeling of devices

testing adjusting balancing Tigard OR 97224

The installation of fire and life safety (FLS) systems is an essential part of both new and existing building. Fire Smoke Dampers (often abbreviated as FSD) are among the most important of them. These devices are installed wherever a heating, ventilation, and air conditioning (HVAC) duct penetrates a fire-rated wall, ceiling, or floor. In the event of a fire, these devices should be able to stop flames and smoke from spreading through the HVAC ductwork, allowing occupants more time to evacuate the building and contributing to the reduction of the amount of damage caused by the fire. However, as buildings and systems age and as physical, mechanical, or electrical problems emerge, dampers can become inoperable. This leaves the duct as an open channel for fire and smoke in the event of a fire, and the facility runs the danger of being shut down owing to a lack of compliance. Verifying and documenting that essential FLS building systems perform as expected is accomplished through the process of testing and maintaining fire smoke dampers.

TESTING OF THE FIRE AND SMOKE DAMPER

fire smoke damper testing Portland OR 97225

Testing for sound and vibration in HVAC systems

Testing for FSD in the states of Oregon, Idaho, and Washington

fire smoke damper testing Portland OR 97225
fire smoke damper testing Tigard OR 97224

fire smoke damper testing Tigard OR 97224

Fixing problems with the exhaust system

The following are some of the ways in which we can assist building owners, operators, and facility staff:

testing adjusting balancing Durham Oregon 97224

Leak testing and investigations on the pressurized and ducted systems

Testing, Changing, and Balancing is an acronym that stands for Testing, Adjusting, and Balancing, and it refers to the process of monitoring and adjusting the flow of air and water to satisfy design criteria. The TAB process involves employing test instruments, sensors, and monitors to check suitable temperatures, airflow, and other parameters inside the HVAC system. This is done in order to complete the TAB process. In order to ensure that heating, ventilation, and air conditioning (HVAC) systems are optimized for occupant comfort, energy efficiency, indoor air quality, and manufacturing processes, testing, adjusting, and balancing is a crucial step for complex air and hydronic systems found within buildings and throughout campuses.

Establishments devoted to education

commissioning portland Portland OR 97225
commissioning portland Portland OR 97225

Performing balance and troubleshooting on air and hydronic systems

Analyses of the quality of the air inside

In addition to enhancing environmental performance and occupant comfort, the TAB services we provide contribute to a reduction in operating expenses for your property. Our team has over six decades of expertise, which allows them to grasp even the most complicated HVAC building systems. They also use the most up-to-date techniques and technology in order to properly and efficiently balance the entire system.

Authorities Having Jurisdiction (AHJ) at the federal, state, and municipal levels have expanded their FSD testing code enforcement efforts beyond the healthcare industry to include the following:

commissioning portland AmberGlen Hillsboro OR 97006

Who requires testing for their fire smoke damper?

NorthWest Engineering Service, Inc., which has locations in Tigard, Eugene, and Boise, Idaho, is committed to maintaining the best standards in the Testing, Adjusting, and Balancing of sophisticated air and water systems. Since 1958, we have been assisting building owners, engineers, and other experts in the design industry to achieve the optimal balance of flow distribution. We are one of the few businesses in the country that has earned certification from both the National Environmental Balancing Bureau (NEBB) and the Associated Air Balance Council. In addition to being a founding member of the nation's first independent TAB apprenticeship, we are also one of the few companies to receive certification from both of these organizations (AABC). We give services that are technically sound, as well as cost-effective, and are based on the procedures that they require.

commissioning portland AmberGlen Hillsboro OR 97006

Frequently Asked Questions

Use tabs to alternate between views within the same context, not to navigate to different areas. This is the single most important point, because staying in place while alternating views is the reason we have tabs in the first place. 

What is TAB? TAB stands for testing, adjusting and balancing of your environmental systems and compressors. The testing part includes the use of specialized equipment to take precise measurements of how your system is operating. 

The key to a comfortable and efficient space is the design and function of a building's HVAC systems. The testing, adjusting, and balancing (TAB) of the systems is what ensures they are functioning properly.

TAB stands for Testing, Adjusting and Balancing for HVAC systems. It refers to the steps taken by HVAC contractors to calibrate the HVAC unit in commercial establishments to achieve optimal performance and air quality. 

First, locate the closest supply air duct to your indoor AC unit. Then use a thermometer, even a refrigerator thermometer will work, and tape it just inside. Let your Air Conditioning run for about ten minutes then check and record the temperature.